8903B HPIB PROGRAMMING MANUAL PDF

programming. HP B Audio The HP B Audio Analyzer and HP E Distortion Analyzer make your audio measurements fast and easy. .. (Does not include HP-IB programming time.) . calibration manual [) and. PDF · HP xA 5xA 7xA 8xA HP-IB Series Programming · HP xA 5xA 7xA 8xA Progamming · HP xA, xA, xA, xA, and. Jun 8, programming instructions when properly installed on that instrument. The HP- IB address switches are located within the Modulation.

Author: Meztirn Tygogal
Country: South Sudan
Language: English (Spanish)
Genre: Marketing
Published (Last): 3 August 2014
Pages: 128
PDF File Size: 17.77 Mb
ePub File Size: 18.75 Mb
ISBN: 313-5-85604-868-1
Downloads: 32115
Price: Free* [*Free Regsitration Required]
Uploader: Doulmaran

The “Z load” pulldown box lets you choose 1, 2, 4, 8, 16, 32,or ohms. Mating Connector HP ; Amphenol When installing the product in a cabinet, the convection into and out of the product must not be restricted. To set it up: Knowledge of these programmkng not be necessary i your controller’s manual describes programming in terms of the twelve HP-IB Messages shown in the left column.

Index of /~kurt/manuals/manuals/HP Agilent

Once the AMPTD key has been pressed, new data and unit entries can be made to select different amplitudes until another source function key for example, the FREQ key is pressed. 89003b not use repaired fuses or short circuited fuseholders. Check, then re-enter correct HP-IB code. If you have not received update information that matches the provramming number of your instrument, you can receive this information through the Update Service. Local Mode Local Capability.

To make this measurement with an oscilloscope, you must first decide the nature of the signal, because from it, the relationship of the peak level to hplb rms level can be mathematically determined. Receiving the Data Message.

Measurement results obtained via Trigger Immediate are normally valid only when the instrument is in a steady, settled state.

  ALGEBRAIC GEOMETRY AND COMMUTATIVE ALGEBRA BOSCH PDF

B Operation and Calibration Manual | Keysight (formerly Agilent’s Electronic Measurement)

These checks are intended to be as independent of each other as possible. During local operation, the Audio Analyzer is allowed to free run outputting data to the display as each measurement is completed.

This indicates the Audio Analyzer properly left serial-poll mode upon receiving the Abort message. The Audio Analyzer is easy to use. The power cord is connected to internal capacitors that my remain live for 5 seconds after disconnecting the plug from its power supply.

VEE runtime libraries What I used: Performance Test 3 Distortion and Noise. Adjust the frequency of the source to approximately Hz until the right display reads -3 dB. All measurement results, special displays, and error outputs except the ” — display are available to the bus.

This eliminates the need to switch between multiple inputs under remote control and reduces software development time and hardware costs. No instrument settings are changed by the transition from remote to local, but all measurements are made in a free run mode.

First, the analyzer contains a flat, wide-range oscillator that can be used as the stimulus. Microprocessor control allows flexible entry of source parameters and versatile display formats.

This would leave the Audio Analyzer in an unknown state. Display the value of V. The right display should show between 9. Distortion Manyal distortion on a spectrally pure signal is created programmign non-linearities in the circuit through which it passes.

Performance Test 6 Audio Filters. Signing Up for the Documentation Update Service Hewlett-Packard offers a Documentation Update Service that will provide you with further updates and changes as they become available. The operation of the instrument is described in the following order: Position the card so the line voltage appears at top-left cover. For instructions on how to 88903b the fuse, refer to Figuresteps 1 and 3. In certain applications, the controller must perform other tasks while controlling the Audio Analyzer.

  AS2200 SMC PDF

The following list includes the name and option mnaual for each available filter. In the ac level and signal-to-noise ratio 88903b the Notch Filter is bypassed.

For those applications where quasi-peak detection is required, the analyzer Serial Prefix A and above can be switched to this type of detection through special functions. The time interval from the Voltage-to-Time Converter is counted. For serial prefix A and above, order H P part number In addition to the programmibg described above, information concerning remote operation appears in several other locations.

This is a captive screw and will cause the top cover to pull away from the front frame. If the fundamental level were 1 Vrms, the second harmonic level would be 0.

The source frequency sweeps, starting from approximately 20 Hz and stopping at approximately kHz. The “Filters” radio buttons lets you select any of the ‘s built-in measurements filters.

Prgramming a serial number prefix that is greater than that shown on the title page indicates that the instrument is slightly different from those documented in the manual. A Hewlett-Packard Interface Bus system may contain no more than 2 meters 893b.

I t calls a t t e n t i o n t o a n operating procedure, ptogramming, or the like, which, if not correctly performed or adhered to, could result in damage to or destruction of part or all of the product. After nine successive occurrences, the display changes to Error DDDD mV range 4. Turn-On Procedure Befor the Audi Analyzer is switched on, all protective earth terminals, extension cords, auto-transformers, and devices connected to it should be connected to a protective earth socket.

Author: admin